기술자료[Sinda/Fluint] Thermal Desktop®(The Advanced Design Modules) 웨비나

The Advanced Design Modules in Thermal Desktop®

: The Advanced Design Modules에 관한 웨비나가 다가오는 11월 14-16일에 개최됩니다.

Given heat loads and material properties, what is the temperature of a plate? That's how our tools work by default. But you can reverse the question too: What heat load is needed to heat the plate one hundred degrees in ten minutes?

That "goal seeking" problem is one example of optimization. Another more complex example might be: What set of orifice sizes should I use at the exits of my heat exchangers to achieve even flows without any one component overheating?

Optimization, combined with Thermal Desktop Measures (thermocouple models), can also be used to automate the adjustment of uncertainties to better match available test data or CFD predictions.

Some uncertainties just can't be adjusted away. Or maybe you don't yet have test data and need to understand how tolerances and environmental variations affect your design.

All of the above tasks are part of our Advanced Design Modules. Come learn about them in a series of upcoming webinars listed below.

Webinar: Introduction to Optimization(최적화 소개)

Tuesday November 14, 2017, 2pm MT (1pm PT, 4pm ET)

This webinar describes the purpose and basic operation of the optimization tools within the Dynamic tab in Thermal Desktop's Case Set Manager. An example problem will be worked interactively.

Prerequisites: Basic understanding of Thermal Desktop and SINDA/FLUINT operation, including Symbols and Registers class or equivalent experience.

This webinar is 60 minutes long.

: 기호 및 레지스터 클래스 또는 이와 동등한 환경을 포함하여 TD 및 SINDA/FLUINT 작업의 기본적인 이해가 필요하며 웨비나는 60분간 이루어질 예정입니다.

Click here to register

Webinar: Automating Calibration to Test Data(테스트 데이터에 대한 눈금측정 자동화)

Wednesday November 15, 2017, 2pm MT (1pm PT, 4pm ET)

This presentation illustrates how to automatically adjust a model's uncertainties to better match available test data. Defining thermocouple locations using Measures and automating comparisons with test data files using Data Logger Compare tools will also be explained. An example problem will be worked interactively.

Prerequisites: Basic understanding of Thermal Desktop and SINDA/FLUINT operation, including Symbols and Registers class or equivalent experience. Basic understanding of how to use the Solver module to pose an optimization problem (attend the above webinar first!).

This webinar is 60 minutes long.

: 모델의 불확실성을 자동으로 조정하여 사용 가능한 테스트 데이터를 보다 더 잘 매치시키는 방법에 대한 웨비나입니다. Data Logger Compare 툴로 측정값을 사용하여 열전대 위치를 정하고 테스트 파일과의 비교를 자동화하는 방법에 대해 설명합니다. 솔버 모듈을 사용하여 최적화 문제를 제기하는 방법에 대한 기본적인 이해가 필요합니다.

Click here to register

Webinar: Reliability Engineering (Statistical Design)(통계설계)

Thursday November 16, 2017, 2pm MT (1pm PT, 4pm ET)

This presentation explains how to use the reliability tools within the Dynamic tab in Thermal Desktop's Case Set Manager. Using these tools, you can estimate the chances that a limit will be exceeded as a function of variability in the design and the environments. An example problem will be worked interactively.

Prerequisites: Basic understanding of Thermal Desktop and SINDA/FLUINT operation, including Symbols and Registers class or equivalent experience.

This webinar is 60 minutes long.

: TD의 Case Set Manager에서 Dynamic 탭 내의 안정성 도구를 사용하는 방법에 대한 웨비나 입니다. 이 툴을 사용하여 설계와 환경의 변화에 따라 한도를 초과할 수 있는 범위를 예측할 수 있습니다.

Click here to register