[ADINA] Tech Briefs : shell structures
Practically Optimal Shell Elements
A shell structure is thin in one direction and long in the other two directions. Shell structures are used in a variety of architectural and industrial applications as they are lightweight, can span large areas, and can be designed to be strong and stiff. Examples of shell structures include stadium roofs, airplane fuselages, ship hulls, automobile hoods and body panels, bridge decks, and oil tanks.
Shell structures are highly dependent on the geometry and boundary conditions. Any small change can have a dramatic effect. When carrying load, the shell structure may be in membrane, bending or mixed strain states, and internal and boundary concentrated strain layers may be present. Curvature is important for the load carrying characteristics of shell structures. A flat shell structure (a plate) subjected to pressure is flexible because it resists the loading only in bending action. A curved shell structure can resist loading in bending and membrane actions and then is much stiffer. Before a building or container that employs a shell structure can be constructed, engineers must analyze the shell structure to ensure it will withstand the necessary loads.
Loworder 3node and 4node Mixed Interpolation of Tensorial Components (MITC) shell finite elements have been used abundantly in engineering practice for many years very successfully to analyze shell structures. MITC shell elements interpolate the transverse shear strains separately from the displacements to alleviate transverse shear locking [1,2]. They perform well in all cases except for bending dominated thin shell structures meshed with elements that are highly distorted outoftheplane (highly warped elements). In this case, MITC shell elements do not behave optimally in membrane action, so that a fine mesh of MITC shell elements may need to be used for accurate results.
In ADINA 9.5.1, a new MITC+ formulation is available for 3node and 4node shell elements, referred to, respectively, as MITC3+ and MITC4+ shell elements, as shown in Figure 1.
Figure 1 3node and 4node MITC+ (MITC3/4+) shell elements
The new MITC+ shell element alleviates shear locking using the same assumed transverse shear strain field as the original MITC shell element and displays better membrane behavior using a new assumed membrane strain field. As a result, the new MITC+ shell element passes all fundamental tests, even for meshes with highly distorted elements and shows practically optimal convergence behavior [3 – 5].
Real engineering structures resist loads in mixed membrane/bending action. However, in this Tech Brief, we focus on tough shell benchmark problems, in which the shell structure resists loads in only membrane action or only bending action, in order to study the behavior of the shell elements in these separate actions. The behavior in combined membrane and bending actions will then be a superposition of the individual behaviors.
Figure 2 shows a tough behaviorencompassing shell benchmark problem of a doublycurved cooling tower (the “hyperbolic shell” problem). If the top and bottom ends of the cooling tower are fixed, the problem is membrane dominated. But if the ends of the cooling tower are free, the problem is bending dominated.
Figure 2 Cooling tower problem
To assess the performance of shell elements, an appropriate error measure must be used. For mixed formulations, the snorm is used [6]. The error measure, , is given by:
where is the displacement, is the strain, and is the stress. We integrate over the 3D shell domain.
The snorm measure used here is the difference between the exact and approximate strains (and the exact and approximate stresses). It can be used for membrane dominated, bending dominated and mixed problems.
The cooling tower in Figure 2 is meshed with 4node shell elements. Figure 2b shows the undistorted and distorted meshes used. For the distorted meshes, the sides are subdivided with ratio 1 : 2 : … : N, where N is the number of subdivisions.
Figure 3 shows the convergence curves for the fixed boundary (membrane dominated) case. Both MITC4 and MITC4+ shell elements perform well for undistorted and distorted meshes.
Figure 3 Convergence curves of the cooling tower problem with fixed boundaries (membrane dominated). The snorm is used.
Figure 4 shows the convergence curves for the free boundary (bending dominated) case. For undistorted meshes, both MITC4 and MITC4+ shell elements perform well. However, for distorted meshes, a fine mesh of MITC4 shell elements must be used for accurate results, whereas MITC4+ shell elements give practically optimal convergence behavior.
Figure 4 Convergence curves of the cooling tower problem with free boundaries (bending dominated). The snorm is used.
Because the new MITC+ shell elements are continuum mechanicsbased elements with a strong theoretical basis, they can be directly extended to nonlinear analysis in a manner that is consistent with the principle of virtual work.
Figure 5 shows a large strain analysis of a conical shell structure that buckles with material and geometric nonlinearities. The conical shell structure is meshed with 3node triangular MITC3+ shell elements, 4node quadrilateral MITC4+ shell elements, and a mixture of 3node and 4node triangular and quadrilateral MITC3/4+ shell elements. Figure 5b shows the meshes used.
Figure 5 Large strain analysis of a conical shell
The movie above, and Figures 6 and 7 show the results. As can be seen, good results are obtained for all meshes of the new MITC+ shell elements.
Figure 6 Loaddisplacement curve of the conical shell
Figure 7 Accumulated plastic strain at final state of the conical shell
In this Tech Brief, we show that the new MITC+ shell elements in ADINA give practically optimal convergence behavior, even when the shell elements are highly distorted.
The new MITC+ shell elements in ADINA are very powerful and strengthens the ADINA offering for accurate, reliable and robust analysis of shell structures.
Keywords:
Shell elements, element distortions, distortion sensitivity, large displacements, large strains, MITC, MITC+, buckling, membrane dominated, bending dominated, mixed strain state, mixed formulation, convergence curves, practically optimal
References
 K.J. Bathe, Finite Element Procedures, 2^{nd} ed., Cambridge, MA: KlausJürgen Bathe, 2014. The book can be downloaded from here.
 D. Chapelle and K.J. Bathe, The Finite Element Analysis of Shells – Fundamentals, Springer, 2003, Second edition 2011
 Y. Ko, P.S. Lee and K.J. Bathe, “The MITC4+ shell element and its performance”, Computers & Structures, 169, 5768, 2016
 Y. Ko, P.S. Lee and K.J. Bathe, “The MITC4+ shell element in geometric nonlinear analysis”, Computers & Structures, 185, 114, 2017
 Y. Ko, Y. Lee, P.S. Lee and K.J. Bathe, “Performance of the MITC3+ and MITC4+ shell elements in widelyused benchmark problems”, Computers & Structures, 193, 187206, 2017
 K.J. Bathe, P.S. Lee, “Measuring the convergence behavior of shell analysis schemes”, Computers & Structures, 89, 285301, 2011
번호  제목  작성자  작성일  추천  조회 
463 
[ADINA] Tech Briefs : Fluid flow through continuously moving narrow gaps using ADINA FSI
ablemax

2020.04.21

추천 0

조회 193

ablemax  2020.04.21  0  193 
462 
열 모델 민감도 분석 & 열 모델 최적화 전문 툴 Veritrek 소개 영상
ablemax

2020.04.15

추천 0

조회 115

ablemax  2020.04.15  0  115 
461 
[SINDA/FLUINT] Thermal Desktop를 이용한 액체수소탱크의 스플래시(Splash) 모델링 영상
ablemax

2020.04.07

추천 0

조회 153

ablemax  2020.04.07  0  153 
460 
[SINDA/FLUINT] 스플래시 패턴 모델링 방법 (Splash pattern and mass of splashed liquid)
ablemax

2020.04.07

추천 0

조회 133

ablemax  2020.04.07  0  133 
459 
[ADINA] 산업별 적용 사례 모음
ablemax

2019.09.19

추천 0

조회 424

ablemax  2019.09.19  0  424 
458 
[ADINA] Tech Briefs : shell structures
ablemax

2019.09.19

추천 0

조회 455

ablemax  2019.09.19  0  455 
457 
[UM] 모노레일/자기부상열차 시뮬레이션 영상 예시
ablemax

2019.08.13

추천 0

조회 582

ablemax  2019.08.13  0  582 
456 
[SINDA/FLUINT] 6.1 업데이트 버전 (Thermal Desktop 유저인터페이스) 설명 영상 안내
ablemax

2019.08.06

추천 0

조회 749

ablemax  2019.08.06  0  749 
455 
[SINDA/FLUINT] 6.1 업데이트 버전 (Thermal Desktop / RadCAD) 설명 영상 안내
ablemax

2019.08.06

추천 0

조회 625

ablemax  2019.08.06  0  625 
454 
[SINDA/FLUINT] 6.1 업데이트 버전 (FloCAD) 설명 영상 안내
ablemax

2019.08.06

추천 0

조회 520

ablemax  2019.08.06  0  520 